Diesel engines are widely used in construction machinery, commercial vehicles, and power generation equipment. Its operational stability is related to the efficiency and operating cost of the equipment. However, in actual use, some equipment experiences abnormally increased oil consumption, sometimes accompanied by abnormal exhaust or reduced power. Burning oil in a diesel engine not only affects normal operation but may also accelerate the wear and tear of parts and shorten the engine’s lifespan.
Therefore, it is necessary to understand the common causes of diesel engine oil consumption and to take targeted measures based on actual operating conditions to ensure long-term stable equipment operation. This article will analyze some common causes and corresponding solutions.
1. Excessive Diesel Engine Oil in the Oil Pan

More diesel engine oil in the oil pan is not necessarily better. Adding too much oil to the diesel engine oil pan will cause the crankshaft to generate greater resistance when rotating at high speeds and will also cause the connecting rod big end to carry a lot of oil to splash onto the cylinder wall. A large amount of engine oil enters the combustion chamber and participates in combustion before it is scraped off by the piston rings. This produces a lot of blue smoke and carbon deposits, accelerating the wear and tear on engine parts.
Excessive diesel engine oil can also reduce the space inside the crankcase or increase the negative pressure in the oil chamber, causing diesel engine oil to surge into the cylinder or leak externally. When checking the oil level in the oil pan, never pull out the dipstick immediately after stopping the engine.
This is because the diesel engine oil that has splashed onto the crankcase wall and cylinder wall has not yet completely flowed back to the bottom of the oil pan. You need to stop the machine for 5 to 10 minutes before pulling out the dipstick to check the oil level and see if it meets the requirements. If there is too much diesel engine oil, open the drain plug to drain some of the oil until the specified level is reached.
2. Severe Wear on Valves and Valve Guides

The valve guides in an engine guide the opening and closing of the intake and exhaust valves. Severely worn valves and guides will increase the clearance between them. This allows the diesel engine oil that lubricates the valve rocker arm to be drawn into the combustion chamber through the gap between the intake valve stem and the guide, where it participates in combustion. Therefore, you must pay special attention to the clearance between the valves and guides when overhauling the engine.
If the clearance exceeds the specified technical specifications, the valves should be replaced. For engines with valve stem seals, prolonged use or the use of unsuitable lubricating oil will accelerate the aging and damage of the valve stem seals. This will also allow some engine oil to enter the combustion chamber through the damaged valve stem seals.
In particular, aged and damaged intake valve stem seals are more likely to allow diesel engine oil to enter the combustion chamber. Therefore, when repairing an engine, it is essential to ensure that the oil seals of the valve guides are properly installed and that the valve stems slide freely within the guides. During engine operation, the specified lubricating oil must be used as required by the instruction manual. Choose a suitable brand and perform regular oil changes and maintenance.
3. Excessive Diesel Engine Oil in the Air Cleaner

For engines that use oil bath air filters, if there is too much oil in the oil pan inside the filter, when the engine is running at high speed, too much oil will enter the combustion chamber through the intake manifold and participate in combustion. This results in oil burning, blue smoke, and excessive carbon buildup, accelerating engine wear and affecting the engine’s lifespan.
Therefore, when adding clean oil to a diesel engine with an oil bath filter, pay attention to the oil level. Generally, you only need to add it to the middle of the upper and lower markings; don’t add too much.
4. Turbocharger Malfunction
For turbocharged diesel engines, if the engine is burning oil and emitting blue smoke from the exhaust pipe, but the engine power remains unchanged, and there is oil residue on the turbocharger compressor port or intake hose, it can be determined that the floating bearing and sealing device on the compressor side of the turbocharger are damaged, resulting in oil leakage.
The diesel engine oil will be carried into the engine intake manifold along with the airflow from the turbocharger compressor and drawn into the combustion chamber, where it will participate in combustion, resulting in blue smoke. When the turbocharger malfunctions, it should be repaired or replaced promptly to ensure the normal operation of the engine, extend the maintenance cycle, and reduce operating costs.
5. Pistons, Piston Rings, Cylinder Liners Show Severe Wear
Excessively worn pistons or cylinder liners will have significantly increased clearance during engine operation. This allows diesel engine oil that splashes onto the cylinder walls to easily enter the combustion chamber and participate in combustion when the engine is running. Simultaneously, poor sealing between the cylinder, piston, and piston rings in the crankcase leads to excessive exhaust gas production, a noticeable decrease in engine power, and a large amount of blue smoke from the exhaust pipe. In such cases, the engine should be inspected immediately. And repair or replace the piston and cylinder liner with new parts according to their wear condition.
Excessive wear on piston rings not only reduces their elasticity and causes them to lose their sealing function but can also lead to breakage. This can weaken the oil scraping and distributing function of the oil ring and may also cause cylinder scoring, resulting in a large amount of engine oil entering the combustion chamber to participate in combustion and expelling a large amount of blue smoke.
To address this issue, when repairing and assembling piston rings without replacing the pistons, the carbon deposits on the old pistons should be thoroughly cleaned first. Then install each piston ring correctly according to the assembly position (pay attention to the position and cut direction of each ring during assembly, and the inner cut surface should face the top of the piston). Replace with new rings and new pistons if necessary.
Conclusion
In summary, there are several reasons why diesel engines burn oil. Therefore, timely maintenance and upkeep of the engine are essential during its future use. Pay attention to the engine’s operating environment, observe its running condition, and select appropriate fuel and lubricating oil according to the engine’s technical requirements. Regular inspections and maintenance can effectively reduce premature wear of engine components, allowing the diesel engine to operate in good condition and extending its service life.
If you encounter issues such as excessive oil consumption, abnormal oil usage, or lubrication problems with your diesel engine during operation, we recommend seeking professional support promptly.
Evisco specializes in industrial lubrication and specialty oil solutions. We have a mature product system and stable supply capabilities and can provide targeted oil usage advice and technical support services for diesel engines under different operating conditions.
For more product information or professional advice, please contact the Evisco team. We will customize a more suitable lubrication solution based on your equipment’s operating conditions.


